A Totally Tipster Bias Tape Tip!

I am making A LOT of 1/4″ inch bias tape to use as vines for my Down the Rabbit Hole Quilt. Yes. You read that right. This bias tape finishes at 1/4″!

My, oh my that is teeny! But never fear. With the right tools it is easy to make bias tape is many different sizes.

I’m sure many of you have heard of or even own a bias tape maker. They are easy to come buy and work so well. They come in different sizes to make different widths of tape.

The picture above is my 1/4″ tape maker. I cut my green fabrics in 1/2″ strips along the bias. You don’t really have to cut on the bias, but I want these little vines to curve this way and that, so I definitely cut on the bias:)

The next step is to snip one end of a strip on an angle and push it into the metal.

On the bottom side is an opening that you can use a straight pin to drag the fabric out just a bit. You only want it a little way out because you want to be able to iron it as it come out.

If you place your tool with the flat side against your board and your iron right up against tip of the opening, you can pull the tool very slowly by the hook and move your iron slowly at the same time.

It works GREAT!

Just look at those cute perfectly folded little edges! It was easy to make a pile of tape in no time at all:)❤️

But how do I remember the size to cut my fabric the next time I want make 1/4″ tape and how can I store these handy tools?

Here is a Totally Tipster Tip for you— I mark my bias tape makers with a scrap piece of fabric!

On the back of the fabric I write the size of strip I need to cut and the finished size it will make. Then I cut a small slit in one end and thread the other end through the slit around the pull. PERFECT!

Now it is easy to know which bias maker to use for the width of tape I want to make.

I have attached sticky hooks to the inside of my cabinet to hang them on. They are easy to find and take up no room at all. Now that is Totally Tipster for sure!! In fact, I call it SWEET!❤️❤️

I hope this Tip is helpful to some of you. Thank you so much for dropping by today. Until tomorrow,

Down the Rabbit Hole at Last!

I am FINALLY starting my Down the Rabbit Hole Quilt by Sarah Fielke.  This is a monthly Quilt Along program that started back in January.  At first I thought I didn’t need another Quilt Along and I really don’t.  Also, I wasn’t overly enthused by this sketch of the quilt.

I mean, really it looks kind of plain in its sketched form.   Sarah is quilting along with us so there isn’t even a picture of the finished Quilt yet.  But as the months got going and beautiful pictures started coming up on my Instagram account, I knew I had to join along.  

I ordered the program back in April, but life has happened and the Long Time Gone, Splendid Sampler, and Delilah quilts were already going.  But now things are calming down, and I am heading Down the Rabbit Hole at last!

I was excited to try out my wedge cutting skills and start my Rabbit Hole center.

I sewed the wedges into four arcs and then joined them to make one wild circle

Isn’t it so cool?  Now you see why I HAD to join along. 

It is so SWEET!!   

Next I started working on my 1/4″ bias tape.  Yep, you heard me right, 1/4″!  Luckily I have a 1/4″ bias tape maker.


Have you used one of these before?  They are great!  I have several in different sizes. I have a totally Tipster Tip for these that I will share with you later this week:)


I folded my fabric to make a bias edge and cut 1/2″ bias strips.  They were so small!

  1. I brought the strip to the ironing board
  2. I stared feeding my strip into the bias tool with the right side facing down
  3. On the bottom of the tool is a slot to pull the fabric down
  4. With a pin I pulled the fabric out

Now that isn’t too hard is it?

Now for the fun part:)

  1. Pin the fabric to the board with the right side facing down.  Do this at the far end of the board so you have lots of room to press.
  2. Place the tip of your iron right against the tool and start to slowly pull the tool against the fabric.  Move the iron along with the tool.
  3. Yea!  A beautiful 1/4″ piece of bias tape. Easy!!

And, what did I do with this teeny bias tape?  Here is a sneak peak!  

I can’t wait to share it with you!  But it is going to have to wait until later though because tomorrow is Scrap Happy day:)!

Until then I hope your day is filled with SWEET creative adventures:)